Windows 2008 server 支援GPT 磁碟
(GPT) 磁碟分割樣式支援的大小高達 18 exabytes(1000,000TB),每個磁碟最多可有 128 個磁碟分割。
以ibm的Storage DS3200來講,插滿12顆2Tb SATA硬碟,可以到24TB,
可在串接三台 EXP3000最多可以達到96.0TB SATA
Windows 2008 server 支援GPT 磁碟
(GPT) 磁碟分割樣式支援的大小高達 18 exabytes(1000,000TB),每個磁碟最多可有 128 個磁碟分割。
以ibm的Storage DS3200來講,插滿12顆2Tb SATA硬碟,可以到24TB,
可在串接三台 EXP3000最多可以達到96.0TB SATA
在 proftpd.conf 的設定檔內加上 UseEncoding local-charset client-charset
Ex:
繁體中文環境 UseEncoding UTF-8 Big5
如此用 不支援 UTF-8 編碼的 FTP Client 連上來, ProFTPD 就會自動轉碼成 client-charset
Review 新公司的備份機制,發現備份的samba server中的檔案都會不見,而且是剛備份完是完整的,隔天檔案就不見了大半,後來檢查crontab job,發現dailly中有一個可疑的script "tmpwatch",原來這個script會定期刪掉720小時未存取的tmp檔案,前任網管又把備份的目錄設在/tmp,難怪會不見檔案,經一事長一智…..感謝前人的錯誤。
新版的Router居然改了預設登入模式,預設帳號Cisco登入過後就失效了,我又臭屁3分鐘完成設定完後習慣就Reload,cisco帳號就無法登入,就變成都無法登入Console了,只能想辦法重設…
重設方法如下:
Start a terminal session with the router via the Console port (telnet will not work for this). Physically reload the router, and from the console repeatedly hit the "Break" key, normally on the upper right hand side of the keyboard.
-You should now be in ROMMON mode. Type "confreg 0x2142" without quotes and hit Enter. Now type "reset" without quotes and hit Enter.
-Allow the router to restart, and hit "n" followed by Enter to stop the startup wizard.
-Type the following command sequence:
enable
conf t
config-register 0x2102
exit
write erase
<Enter key>
reload
The router will now boot normally, with a factory default configuration, even if you did not know any of the password(s) securing the router.
Problem:
機器從待機或休眠中恢復時PCMCIA卡無法被識別,系統為Windows XP。
Solution:
不需要更換硬件。請下載並安裝一個Hotfix補丁即可解決問題。鏈接如下:
如果系統已經安裝了Hotfix補丁但問題仍未修復,請將下述內容存為一個.reg註冊表文件,運行並導入即可:
Windows Registry Editor Version 5.00
[HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\usb]
"USBBIOSx"=dword:00000001
"EnSoftRetry"=dword:00000001
"EnIdleEndPointSupportEX"=dword:00000001
"EnIdleEndPointSupport"=dword:00000001
"EnableIdleTimer"=dword:00000001
先將mysql停止
#service mysqld stop
將mysqld啟動並設為無登入控制模式
#mysqld_safe --skip-grant-tables&
登入mysql,注意喔,我沒輸入帳號密碼
#mysql
重新將mysql上的root密碼設定為1234
mysql> update mysql.user set password=PASSWORD('1234') where user='root';
讓剛剛的命令生效(修改或刪除帳號必須手動生效)
mysql> flush privileges;
離開mysql指令列
mysql> quit
重新啟動mysqld
#service mysqld restart